Shopping Cart
0 items
 

DIGITAL TEMPERATURE CONTROLLER GAUGE ALARM ENGINE WATCHDOG CAR OVERHEATING PROBE

DIGITAL TEMPERATURE CONTROLLER GAUGE ALARM ENGINE WATCHDOG CAR OVERHEATING PROBE
Click to enlarge
Price: $42.99
Availability: In Stock
Model: DWH7016H-12V
Average Rating: Not Rated

  

ENGINE GURDIAN OVER HEATING GAUGE ALARM FOR OIL or WATER TEMPERATURE

 

 

Displays your true engine temperature and If the engine overheats(alarm set point), the Temp controller will start beeping and also visual guide HHH on the controller screen intermittently to warn the driver.

The heat sensor simply fits like a washer under any suitable bolt that is close to the cylinder head or engine block like under tappet cover bolt or thermostat housing bolt or similar. If you want to check the radiator temp, you can connect Temperature Sensor to the upper radiator hose too. The sensor detects changes so quickly, drivers can see their engine temperature rise and fall degree by degree (with 0.1 degree resolution) as they drive in varying traffic and road conditions.

you don't even need to know your engines temperature specifications to set the overheating alarm. You simply note the highest temperature your engine reaches during normal driving, then set the audible alarm to go off at a few degrees higher. This controller can be set to alarm at any temperature from -50 to 110 degrees C. The controller can also use to monitor the temperature of Air Cooled Engines, Transmissions, Gearboxes, Transfer Boxes & Wet Exhausts in fact anything upto 110 degrees C (230F) for professional racing car and It can be fitted by any handyman. The main unit fits under the dash (Compact size - 75 (W) x 86 (H) x 35 (D) mm, plus mounting tabs . The power just connect to 12V DC by wire.

 

The Controller has 3 relay output too (one, first heat set point output and second, heat alarm output with beeper and third, cold set point if you need ), and you can connect the outputs to any devices that you need run when you have emergency overheating like, control the extra coolers by your controller .so if your cars has two cooler or you installed 2 extra Cooler, you can set one of the coolers to kick lower temperature to give you stable control over your temperature.

 

This system can help to prevent overheating due to:

- Coolant loss

 

- Hose leaks

 

- Malfunctioning thermostat

 

- Blockage in the radiator or radiator hose and cap

 

- water pump failure

 

-Oil system problem

 

- Air flow restriction

  Features:  

 

  • Mini and light design
  • Large and clear LCD display
  • Temperature Range -50 ~ 110 °C (-58 to 230°F).
  • Dual heating and cooling function
  • Control temperature by setting the temperature set value and the different value
  • Temperature Calibration
  • Wiring diagram for installation included

 

Temperature Controller Specifications

 

  • Temperature Measuring Range: -50 ~ 110 °C
  • Control temperature range: -50 ~ 110 °C (adjustable)
  • Control temperature difference: 1 - 15 °C (adjustable)
  • Auto switch between heating and cooling
  • High alarm set point with buzzer
  • Resolution: 0.1 °C
  • Accuracy: ± 1 °C (-50 ~ 70 °C)
  • Sensor error delay: 1 minute
  • Relay contact capacity (Heating): 10 Amp
  • Relay contact capacity (Cooling): 10 Amp
  • Compressor delay protection time: 0 ~ 10 minutes (adjustable)
  • Operating Temperature: 0 ~ 60 °C
  • Storage Temperature: -30 ~ 75 °C
  • Operating Relative Humidity: 20 ~ 85 % (No condensation)
  • Power Supply: 12 V AC/DC
  • Power consumption: < 2 W
  • Cable length: 3 m (near to 10 feet)
  • Define LS or HS (Lower and Higher set point) between -50 to 110 C
  • Item dimensions: approx. 75 (W) x 86 (H) x 35 (D) mm (2.95’ x 3.39’ x 1.38’ inch)
  • Item weight: 180 g

 

Thermocouple Specification

 

  • Measurement range: -50 to 110 C
  • Cable length (L): 10 ft (3m)
  • Sensing tip material : washer type cupper sensor
  • Washer inside diameter : 6.2mm
  • Sensor type: Negative Temperature Coefficient NTC sensor

 

Wiring work

 

The unit is panel mount design . This unit is supplied with wiring diagram of how to fix the main unit to your application systems.

 

 

One Set Included

 

  • 1 x Mini-Temperature Controller
  • 1 x Temperature sensor probe with 3m cable
  • 1 x Instruction Manual

Wiring &  Manual

Write Review
Your Name:


Your Review: Note: HTML is not translated!

Rating: Bad            Good

Enter the code in the box below:

DIGITAL TEMPERATURE CONTROLLER GAUGE ALARM ENGINE WATCHDOG CAR OVERHEATING PROBE
Click to enlarge