USB PID Temperature Programmable (Ramp & Soak) Controller with SSR output and universal type input with Fahrenheit or Celsius display

This controller can connect with USB to your computer and you can program, monitor, record and control the process by your computer. The software has a lot of functions like,

-Write unlimited program and save your program with related name for future use

-Monitor and record temperature on Excel or graph by your needed interval time

-Easily Change or make you program on your computer and upload your program on your temperature controller in second

-Change the software setting for your needed reports

The software support windows and does not work with MAC

Use this Ramp & Soak PID Programmable Controller when you wish to precisely control the temperature of a kiln/heater/cooler on certain timely cycles.

Can be programmed for multiple profiles up to 60 Ramps and soaks (30 segments for Ramp+30 segments for Soak).This controller is easy to program and comes with a user friendly manual.

Applicable industries:

- Annealing

- Jewelry

- Beer Brewing

- Ceramics

- Metallurgy

- Petrochemicals

- Kiln, Oven, Furnace and etc.

The item includes: Ramp and soak controller+Free Software+ USB Converter (for connecting temperature controller to your PC)

If you need wire for USB Data transferring please click Here

Features & Specifications:

High accuracy 0.2%FS
Can have several different programs
Up to 60 segments (30 ramps and 30 soaks)
Be able to run/stop/pause/jump the program
With soft-start function
Built-in Switching Power Supply
Auto/Manual control switch from front panel
Configurable time-dominate or value-dominate controls
Modularized design
Program, Monitor, Record and control by your PC
The time configurable between minute and second
Equipped with differential gap, decimal point for all input, Auto tuning (with learning stop or start), alarm output configurable with 8 different options, system function (heating or cooling),......

Available Segments	Up to 60 segments available for a program
Detective Temperature Range	-200 to 1800 °C (depends on input type)
Patterns	Be able to program different patterns with different segments
Input	Thermocouple: (K,S,E,J,T,R) RTD: (Cu50, PT100) Linear Voltage and current:0-5V,1-5V,0-1V,0-100mV,0-20mV,0-60mV,0.2-1V(100-500mV),-20 -+20mV(0-10V) -5V- +5V(0-50V), -100 - +100mV(2-10V) Linear Resistor:0-80 Ohm, 0-400 Ohm
Output	Voltage pulse to drive SSR
Control action	Heating , Cooling
Response time	Less than 0.5S (configurable)
Accuracy	0.2%FS+- 0.1C(Cu50 cooper resistor compensation or ice point compensation) 0.2%FS+0.2C (TC input and internal compensation)
Temperature drift	Less than 0.01%FS ⁰C (Typical value is 50ppm/⁰C)
Resolution	1⁰C or 0.1⁰C(automatically change to 1⁰C when the temperature is higher than 999)
Display	Dual line - four digit - LED display
Decimal points	Configurable for all inputs
Control Method	ON/OFF AI MPT with auto tuning, adopting fuzzy logic PID algorithm
Auto/Manual Control	Auto/manual bump less transfer from front panel
Auto-tuning	Auto-tuning and manual tuning available
Alarm Mode	Absolute value high limit, Absolute value low limit, Deviation high limit alarm, Deviation low limit alarm.
Alarm stand by	In some occasions, for example, in the heating process, when the alarm is set to as low deviation alarm, right after the power is turned on, the alarm will be triggered but there is no problem in the system, the alarm block function can solve this problem.
Soft start function	In some particular application, 100% output ratio is not allowed when the power just turned on; soft start function is a great feature to solve this problem.

Power Supply	90~260VAC
Dimension (DIN 1/16)	48mm48mm90mm
Mounting

Manual

If you cannot download the software please right click on the hyperlink to the software and select “open link in incognito window”. And then on the new incognito opened window select the URL address on the URL bar and click enter and it starts downloading the software.

Software

In order to see how the software works, please check the following video link,

Software Training Video